How to make a regular coin ring. How to make a ring from a coin. Choosing the right coin

Owned by Nicholas Heckman. He independently took up the hammer and created such an accessory for his beloved. The girl was amazed, however, like all her relatives. The general admiration inspired Nicholas so much that he began to improve his creation and, as a result, released a whole series of original silver rings, but after that he stopped his business. Today, everyone can do this work for his beloved. A homemade ring will be a great surprise, because what is most valuable is what is created with your own hands.

What is needed to make a coin ring?

First of all, you will need a plastic hammer, bolt, drill, or any other tool with which you can make a hole. This can be, for example, a special apparatus. Use what is convenient for you. Prepare sandpaper to add shine. It will come in handy after completing the main work.

How to choose a coin for a ring?

It should be noted that it must meet certain requirements. Main characteristics:

• strength;
• safety;
• the size;
• Colour.

Brass, silver, bronze and steel are not hazardous to human health. That is why you should give preference to these particular materials. Copper and nickel can cause skin diseases and body poisoning.

Pay attention to size. Small coins, up to 1 ruble denomination, will definitely not work.

DIY your ring: step one

First, decide which coin you will be making the ring from. Silver is an excellent material. Then heat it red-hot to make it elastic, but don't overdo it. Otherwise, the coin will be deformed, and some of the elements will be lubricated. After it acquires a red hue and slightly whitens, drop it sharply into cold water. At this point, you will hear a hiss. Do not be alarmed - this is a common occurrence.

We pass to the main work to make a ring from a coin with our own hands. Use a drill to make a hole. Make sure it is even. The larger it is, the thinner the ring, but don't overdo it. Otherwise, the coin may burst.

Once you have made the hole, you will need a plastic hammer and bolt, thanks to which you can select the required size and create the shape. This tool is like a metal stick that expands from the bottom to the end. Put a coin on the bolt and with even hammer blows lower the ring down, stretching it. This is a very painstaking process. Try to tap the product lightly, otherwise it may deform. Gently adjust the ring to the size you want. There is a special marking on the crossbar. When you get to a certain level, remove the ring.

What do you need to know?

To make a ring from a coin, you only need to use a plastic hammer. If you use metal, you risk damaging the smallest elements of the coin. Accordingly, the surface of the product will turn out to be uneven, even after sanding.

Making a ring from a coin is not easy, however, if you follow the rules, you will certainly succeed. There is one more very important nuance. To prevent your product from taking on a conical shape, from time to time remove it from the crossbar and turn it over. This is the hardest part, because choosing the right size is not as easy as it seems at first glance. Follow the instructions carefully, and you will certainly be able to make a ring out of a coin.

When removing the item from the deadbolt, use a pair of pliers or clamping pliers to avoid scratching it.

Safety regulations

When working with hot metal or silver, be sure to wear special gloves, because you risk getting burned. It should be noted that at the first stage of manufacturing, when you work with a drill, you need to wear or a mask. Equip your workplace in accordance with all safety regulations. When punching a hole in the coin, cover the table with a sheet of fiberboard.

Grinding

When wondering how to make a ring from a coin, you need to carefully familiarize yourself with the manufacturing process. All instructions are detailed in this article. As we said, the most difficult part of the work is creating the form. Sanding is the most enjoyable process. When the ring is ready, you can enjoy the fruit of your labor to the fullest. It remains only to add gloss and shake off excess husk.

Create shine and bring beauty

In order for the surface of the ring to turn out smooth, you can make several dozen blows with an ordinary spoon. They must be light, otherwise you risk deforming the ring. To make it smoother, use emery paper or a special electric tool to remove any exterior imperfections. The surface of the ring, the photo of which you see below, will take on a polished look.

It should be noted that there are several types of polishing tools: coarse grain and rough. Choose what suits you best.

The manufacturing method used in this article is quite complex, but the result is a perfect piece that will delight you for years to come. After polishing, you can decorate the ring with a beautiful engraving or original pattern. However, the result of your work depends on your efforts.

How to organize your workflow?

It is necessary to prepare a workshop where you will have everything at hand. Choose soft alloy minted coins as your material. Always remember this, because the preparatory process is no less important than the work itself.

What other technologies are used to make a ring out of a coin? As you know, there are several methods. The second can be used as an alternative. It begins with the fact that you need to put a coin on the edge and cover it with some form. An ordinary spoon is suitable for this. This manufacturing method differs from the previous one in that the coin does not need to be melted. Here it is necessary to flatten the rib, applying strong blows hammer. Work the edges evenly. Periodically look at what happened. After the edges of the coin are rounded, drill the hole, but not completely. Stop the drill before it goes right through. Then sand the inside and sand the outside.

How to make your ring perfect? Take an abrasive compound and apply it with a small piece of cloth. Wipe several times to achieve a mirror finish. After that, prepare a grip, due to which you can firmly hold the coin in your hand. It is necessary that his lips have a curved shape. This will provide protection from dents and unwanted scratches. You can also use rubber felt or paper backing (any soft material will work).

The next step is to enlarge the hole in the center. Make sure that the drill does not slide to the sides, otherwise all the work done will go down the drain. At this stage, you need to be patient. Use gentle and painstaking movements to highlight the circumference of the ring. After you have made the ring of the required size, you need to level the inside with an emery roller.

Making a ring from a coin is a rather painstaking process. It requires precise movement and adherence to instructions. There are many technologies. You can use a variety of crafting tools. For example, you can use ordinary pliers as a clamp, wrapping them with soft material. This will prevent damage to the surface of the product. There are also many different polishing machines available to make the process easier.

A coin ring is an original and romantic gift. Any girl will appreciate such a broad gesture.

More and more often on the Internet there are photographs of rings made of coins, they look very beautiful and unusual, but it is not so easy to buy such a ring so that it also fits on your finger and is not expensive. But if you get used to it, then such a ring from a coin can be made at home with your own hands.

To make a ring from a coin, we need:

• Coin;
• Vice;
• Drill with a set of drills;
• Blowtorch;
• Hammer or chisel (you can get a better wooden ring, but the process will take longer);
• Metal conical pins and reinforced plastic pipes;
• Sandpaper and GOI paste.

How to make a ring from a coin with your own hands, step by step instructions:

First you need to mark the center of the coin with a center punch and hammer. Then we will need to drill a hole, for this we need to gently clamp the coin. This is done this way, take two boards (one thin and the other of any thickness that suits you) or plywood a hole is drilled in one of them, then put between these boards, so that the intended center of the coin is exactly in the center of the board hole and these two boards are compressed with clamps. , our entire coin is securely fixed and you can drill a hole in it with a small diameter. After that, the hole needs to be sanded so that it is smooth and ready for further action.

Next, you need to heat the coin to red with a blowtorch or a gas burner, this will allow the metal to be “released” and the coin will not break when it is further unrolled on a cone and will make it more plastic and pliable. Then we immerse it in water.

Now we put our coin on the conical pin and begin to slowly beat the coin from above, unfolding it, it is better to use a wooden chisel for this, it will allow you to keep the drawing of the coin intact, and in order to unfold the coin, you can take a pipe that fits in diameter, which would fit on the pin and with careful blows on the base of the pipe, we push the coin further and further onto the rod, increasing the hole to the diameter we need (under the desired finger thickness). We would like to note that this is the most time-consuming and difficult part of the work, since at this stage you can easily damage the coin and you will have to start all over again with a new coin.

After all this, we should end up with something like this:

To prevent the ring from getting a conical shape, it must be removed and turned over from time to time during molding. We bring it to such a state that the cone shape is removed and it becomes the required diameter.

If after the work done by us the ring began to meet our requests and the drawing remained intact, then you can proceed to the next final step - polishing. This can be done in a variety of ways, such as using the Dremel with the correct brushes and GOI polishing wheels. You can also polish it by hand, the main thing is not to spoil the drawing. Before polishing, it is better to warm up the ring again and toss it into the water, when the scale comes off the pattern will appear better.

Thus, you can make rings of various thicknesses (wide or thin) from coins, those who are seriously engaged in the creation of rings from coins buy collectible coins for their work, but if you are just a beginner, then it is better to make the first ring from a coin from more affordable coins, since there is a great risk of spoiling it. This is far from the most the only way make a ring from a coin, you can find others on the network, but this is perhaps the most affordable of them.

Examples of how coin rings work:

Unique things always attract our views and interests. Today, you can make yourself special by putting on your hand a ring made from a coin. Exactly the same you will not find anywhere else, so let's learn how you can do it yourself. It will take a lot of time, but it's worth it.

How to make a coin ring at home?

Before you start making a ring, you need to find a good and beautiful coin. As a result, we will get a ring where the coin will be partially displayed, so the more beautiful it is, the better the ring will look. After we have picked up the coin, we can proceed!

1. Take a piece of steel to make a good support on the work surface. Next, we put a coin on it and hold it in an upright position. Now we need to take a spoon or a small hammer and start knocking on the edge, rotating the coin all the time. You need to beat the coin evenly and the blows should be the same.

Here's what we get after a while:

This is the most difficult stage, it can take a lot of time.

Continue shaping until the ring fits on your hand.

2. Once the coin has been sized to the correct size, the middle must be cut out. For this we use a drill, and a drill for metal. Before that, you can walk with fine sandpaper on the outside of the ring.

We try to make the hole as large as possible.

So we got our result, a ring made from a simple coin!

Nowadays, when it is difficult to surprise people with something, but you really want to, you can do stylish ring from a coin that will amaze others. Especially if you choose an unusual specimen. For the first time, a way to make rings from metal kopecks was invented in America, and the person who did it was called Nicholas Hackman. They say that when Lenin married Krupskaya, they exchanged rings of coins. Now this idea gives enterprising people good earnings because such rings are sold for good money, and they are in demand.

There are two manufacturing technologies: one is simple, and the second is a little more complicated, but if desired, everyone can master it, you just need more tools. Let's start with the simpler one.

How to make a ring out of a coin

A ring can be made from absolutely any coin. If you wish, you can take a silver or gold one. To turn the ring into a coin, we need:

• A spoon.
• Drill.
• Zeal.

In the process, everyone will have additional tools with which it will be convenient for him to perform actions at a certain stage. If the ring is planned to be thick, then you need to take the appropriate coin, for example, a penny, in general, it should be larger in size than a finger. It is not recommended to take multi-layered pennies, at least until there is sufficient experience in manufacturing.

So let's get started. You need to take something metal, you can, for example, a hammer or other even piece of metal, put a penny on top of it on top of it and, holding it with your fingers, beat along its edge with a spoon. Doing this will take a long time, so you need to be patient. This is the only way you can understand how to make a ring out of a coin and whether it is worth it. It is better to take a massive spoon so that it is more convenient to work with it. You need to beat about three times, then turn a penny and start working further on a new site.

Production nuances

In this case, the main thing is to knock often, but not very hard, so that the surface from the blows gradually expands and is smooth. If you hit too hard, dents can appear and ruin the whole look. Another nuance is that you need to evenly tap the coin from all sides so that the surface is flattened evenly. It is worth developing a rhythm and moving in it constantly.

You need to continue knocking until the penny reaches the desired size. Making a ring from a coin requires a good eye. When the size of the jewelry becomes visually close to the desired one, you need to start measuring the diameter with a caliper in order to observe the exact parameters.

Drilling a coin ring

To drill a coin, you need to fix it. This can be done in a vice, after placing wooden blocks so as not to scratch the surface. If there is no vice, you can take two pieces of board, drill a hole in them by a millimeter or two smaller penny. Connect two bars and make small holes for self-tapping screws in the corners. After that, we insert a ring between the boards so that through the drilled opening there is access to the coin. We fix it securely and, holding this massive structure well, drill through the money. When we make a ring out of a coin, it is better to screw it on before drilling so that the drill does not jump off and does not scratch the surface.

Expanding the hole in the ring

Without pulling out of the clamp coin ring, you need to expand the hole in it. To do this, you can use a large drill or a round file of a suitable diameter by inserting it into the drill. In short, if there is no special instrument, then you just need to improvise.

Grinding the outer part

Now we already know exactly how to make a ring out of a coin, and it remains to polish it to a mirror shine. To do this, you need to take a bolt and nut of a size that is very close to the diameter of the inner circle of the decoration. We put it on the bolt, placing a piece of cloth, and then fix it with a nut. It is very important that the ring does not come into contact with metal or get scratched. We clamp the bolt into the drill, turn it on and grind the ring, first on the finest sandpaper, and then on felt or thick cloth. So the appearance of the ring will become dazzlingly perfect.

The inside can be easily sanded by inserting a straight piece of stick into the drill instead of the drill. You can hold the ring with pliers, having previously wrapped them in a thick cloth in several layers. That's all - the ring is made with your own hands from a coin, now it is worth polishing it by hand, and the fashion accessory is ready.

Ring with external coin design

To turn the ring pattern outward, you need to take a slightly different approach. This method is more complicated, but the result is many times more interesting.

The manufacturing scheme differs radically from the first option. You need to immediately drill a hole in the coin of such a size so that the rim matches the thickness of the ring. After that, it will need to be expanded using a metal cone. It is firmly installed, a coin is put on top, on which we put a plastic tube and lightly hit from above. The coin gradually decreases, expanding at the same time. When doing these steps, you need to feel the metal and watch the product to prevent the ring from breaking. After the coin has dropped a little, it must be removed and heated. This can be done in a fireplace or with a gas cutter.

After the penny heats up, you need to continue the same actions as before, only with a red-hot product. We do everything gradually, each time removing and heating the future ring. When the large circle, which is closer to the bottom of the cone, becomes of the required diameter, the product is turned over and is also put on the cone in a red-hot state. The work continues until both circles are of the same diameter. Here's how to make a ring with a pattern on the outside of a coin. After that, you need to grind the ring, as described in the first method.

It is not necessary to completely remove all carbon deposits when sanding. With a combination of shine and carbon deposits, the metal looks very impressive, and the pattern of the coin gives the ring a special charm. Such a stylish accessory will definitely be noticed by everyone around.

Hi, people with hands from the right places and just sympathetic.

I would like to tell you how I learned how to make super cool coin rings. But no. Super-cool did not learn.
Anyway, so far I have not reached the level of "well, everything, now you can and at rest", so let's call them just ordinary rings made of coins.

Under the cut, the path through thorns, garage workshops and the suffering of numismatists.

It all began four years ago, when the post “how to do it easily and simply” began to circulate actively on VKontakte. There were 9 photographs, in two of which they beat a coin with an iron hammer, and then it was all so beautiful and unharmed. It used US quotas (25 cents) and I had a bunch of quotas from a recent trip on my desk. This is a sign, I thought, and forgot about this post for two months, leaving the quarters covered in dust.

According to the laws of the genre, I came across this post regularly enough that at one point I realized that I hadn't had any new hobby for a long time and wondered how it was actually done. I took a few five-ruble coins, a couple of cans of beer and went to the garage to experiment. Now I understand the importance of the accident that I came across coins issued before 2009, copper-nickel, and not modern steel.

A couple of hours of experiments have shown that a “don't throw anything away” garage is good, but even that is not enough to comfortably work with unfamiliar material and a little specific tool is required. For example, punching discs, because when drilling with a drill, terrible nodules remained and the coin was bent from heat and pressure. Or a jewelry crossbar, which at first I tried to replace with some random, rusty, barely tapered piece of iron. Before the appearance of the video of the lawyer Yegorov, where he turned the bolt with a grinder from reinforcing bar in a lathe, about six months remained.

Googled YouTube, first ours, then foreign ones. I found out that a) in Russia no one does this, b) in the states it is almost on stream and is in demand, c) initial investments are almost not required and everything is done quite simply (three times ha ha). The only conclusion was made - we must jump. Gutted the stash, went to Jewelry Tools, left the stash. In fact, the basic jewelry equipment (cutting, bolt, plastic hammer) required only about 5 thousand rubles. If I ordered all this on Ali, it would have turned out much cheaper, but I needed it here and now. You yourself know how it happens.

In fact, the manufacturing process itself is quite simple, although it is somewhat specific in terms of the tool used and is more like a manual for a lathe. Everything seems to be clear, but incomprehensible.

Of the tools you will need:

Jewelry tool:
- Cutting discs, such as this. It is possible with a drill, but it is long and inconvenient. On Ali, of course, there is also a felling:

Rigel, this is such a metal cone, without it there is nowhere, you can carve it out of reinforcing bar like Lawyer Egorov or, again, in Ali, you just need to look to make sure it is steel (not plastic) and smooth, without steps:

A common tool: a vernier caliper, a vice (you can do without them, but it is more convenient with them), a regular hammer, a plastic (or textolite) hammer to save the pattern on the coin, a 20 cm piece of pvc pipe (preferably of different inner diameters ± according to the size of the desired rings), file, fine grain skin, polishing (goi paste, for example).

The algorithm is as follows:

Find the center of the coin, cut a hole about 10 mm in diameter. Cutting or drilling

We put the resulting washer on the bolt and tap it with a plastic hammer so that the edges of the coin begin to bend down.

Bending the washer at least 45 degrees, turn the bolt horizontally, resting the coin on some plate. We continue to knock on the coin so that it continues to press against the crossbar.

We turn over the coin on the crossbar with the wide part up. We put on the crossbar a piece of plastic pipe, resting the end on the coin and knocking with an ordinary hammer on the pipe from above, upsetting the coin below. The point is to remove the taper of the ring by making its walls parallel. We try not to overdo it with stretching, because without jewelry anchors and a vice, you will not be able to reduce the size of the ring.

We remove the ring, with a file or a coarse sandpaper, we clean the edges, then with a fine one, then we polish.

Done, you are amazing! But I warned that it looks like a lathe manual.

I used this algorithm to make rings for the first six months. Now the process has become much more complicated (but faster), and new tools have appeared in the equipment fleet, from a ring stretcher (pinocchio) to special cones ordered in a turning workshop.

However, even then there was enough enthusiasm that even a friend's broken finger would not prevent me from making it work. The plaster helped to keep the dremel correct.

About a year later, I finally learned how to work with silver. It was really a great achievement because before that silver coins broke in about half of the cases, which did not add optimism at all. It turned out that he simply annealed the silver incorrectly. The moment when jewelry education WOULD come in handy, but Google really came in handy. From the same series, the moment when I cooled a steel coin red-hot during annealing in water and could not understand why then the hammer crumbled against it. Literally "How the steel was tempered."

But, of course, it was not done without a variety of first pancakes, and it still cannot do. The box with "Pinocchio curves" is regularly replenished, albeit at a slower pace than the "ready-made" box, which is good news.

I worked then, three years ago, with a friend in my garage. There is, of course, a junk warehouse, like in any garage where the car is not parked. Well, a couple of free square meters for us. We don't need much. And once they call, they say, "We are here from the local television, found out about you, we want to come to the workshop, shoot a report." We were a little shocked, a little starred and, in our joy, said such nonsense to the whole TV that it’s still a shame to watch. And all this in a garage littered with rubbish.

Another "once" a friend wrote to me. “I’m here,” he says, “I’m organizing a cosplay festival, will you sell your rings there?” This is how the era of hand-made markets opened for me. First locals in Yekaterinburg, then in neighboring regions. Last year I went to Moscow twice. We were warmly welcomed, thank you.

With these markets, I had to reactivate the skill “make something out of nothing” and create a stand. I didn't want typical jewelry, I'm a creative person, so this miracle was born. Plexiglass figure eight, laser cut slots, end rgb-tape and top illumination that went from "and so it will come down" to a LED strip for 1600 lumens.

The year before last, due to circumstances, I had to leave my native warm garage and urgently find a replacement in the capital box. There my dream of a separate workbench came true. I extended the legs of an ordinary office table, pulled everything together with corners and firmly attached them with corners and anchors to the floor and wall. Of course, it's not worth knocking on it with a hammer, the tabletop vibrates from impacts, but the vice and Pinocchio hold confidently, nothing crawls anywhere and is generally pleasant.

Over time, in the manufacture of rings, I wanted more in the truest sense of the word. Large coins are always more attractive than small ones, and the US craftsmen have mastered them long ago. Again, Google helped find the dreaded swedish wrap method, which essentially means pressing a finished ring into a polished inner cone to reduce size. It comes in very handy here, to protect the design of the coin, the plumbing Teflon sealing tape came in handy. And pvc pipes. And balls from bearings. And also all sorts of unknown garbage, which is beautifully laid out on the workbench in the previous photos. A complicated method, I say. But it turns out well.

So I got close, in fact, to the cherry on the cake. For a very long time I went to her - two years, almost. The first thought to make a GIF of creating a Morgan dollar ring arose when I made the very first animation from copper cents and immediately wanted to raise the bar. But then I still did not know how to work with silver. Then the second problem arose - the size of the coin. For the technologies existing at that time in my workshop, the coin was too large, 38 millimeters is not a joke. But that was also resolved (the largest coin I have worked with so far is the 1937 British crown, 38.6 mm). True, the GIF was still far away. It's one thing to learn how to make rings from such a coin, it's another thing to find the time, place and situation to film the process of creation. I will not describe typical everyday problems, everyone knows them, but they took several more months.

But, like everything in the world, it finally happened. Three hours of production and filming, five hours of processing and creation, totaling 8 hours of work for a 15-second animation. Amazing efficiency. Tag sarcasm.