How to make a ring from 10 ruble coins. We make jewelry with our own hands - a stylish ring made of a coin. How to make a ring out of a coin

The year of manufacture is minted on the coins. This means that you can make a ring from a coin with a significant date for you or the person to whom you will give your product. This will be an original themed gift made by yourself. The method proposed by the author of this idea is suitable for any coins.

To make a ring from a coin disk, you need to make a hole in it and then unfold the resulting blank with a Morse taper. The smaller you make the hole, the wider the ring will be. However, it will be difficult to make a wide ring, since when unfolding the coin, you will have to try not to tear it or crush it.

The actual work on turning the coin is carried out with a stand with a wide opening. To do this, you can use a bearing, pipe end or other device. Warming up the workpiece, you can protect it from rupture. Experience has shown that paper is a good protector that can protect the inside of the ring from damage. To push the workpiece, it is advisable to take an aluminum tube, since this metal is softer and will not damage the future ring.

After creating an annular blank, only the grinding of the product remains.

The second helpful video from this master is on the topic of coin rings.

As additional information, another video on the same topic, but with the approach of a foreign master.

And here is another video tutorial on this topic.

Unique jewelry has always attracted attention, just remember what battles unfolded in the Lord of the Rings. In this video you will learn how to make a unique ring with your own hands from regular coin... In our case, it will be in rubles.

Mark the center of the coin and make a hole in it. We cut the resulting burrs with a file. Then we need to put this blank on a metal rod. In the case shown, this will be a core. Having made an emphasis on the board, we begin to gently tap it and this must be done at an angle to the workpiece so that the side of the coin with the pattern begins to turn outward.

Our workpiece has outgrown the core and now, to further bend the sides of the money and enlarge the hole, we will use a machined sleeve from the key and then a processed construction plumb line - ideally, it is better to have one rod with an increase from small to large diameter. If there is a vice, then they will greatly simplify the task. But be careful, the vice can ruin the drawing.

Let's warm up well and start forging ours. This process is very time consuming and you can hardly manage it in one hour. After we have achieved the desired size of the ring, we will grind its ends on a grindstone and then process the edges with a round file.

When making the first coin, 2 mistakes were made that you want to avoid. The author of the video did not immediately use the heating of the coin and polished the ring too much, but it turned out but without a pattern.

Let's try again. Let's make a ring from another 1 ruble coin. Let's make a hole, warm it up well and start forging. We repeat this process until we get the desired result. After the ring has taken the desired shape, we will process the edges. Next, we will begin to carefully sand it, and the most important thing here is not to grind off the entire drawing. With a little skill, many will do much better.

In an age when much is available and it can be quite difficult to choose an interesting, mesmerizing gift, a coin ring becomes thus original present that you want to make to your loved one or even yourself. For the first time, such rings began to be made in the USA, and later this method of making unusual jewelry spread throughout the world. Today, such products are sold at high prices and are very popular.

Features of creating a ring from a coin

Experts in this field note that a coin ring can be easily made by yourself, having in your arsenal the necessary working tool. However, at first glance, the instruction for the production of jewelry is stupid and makes you feel insecure.

You should also choose the right coin for the production of jewelry. Experienced jewelers note that pennies minted from silver, brass, steel or bronze are suitable. Also, they must be of the required diameter so that the ring does not turn out to be too small.

Important! Parts that contain copper and nickel are completely unsuitable for the production of such jewelry. A product made of such an alloy can cause allergic reactions on the skin and provoke poisoning.

When choosing a material, attention should be paid to the safety of the material from which the coin is made, its color, size and strength. After making sure of the quality and safety, you can start producing jewelry on your finger.

What will it take to make a ring from a coin with your own hands?

Any man who has a large supply of tools in his arsenal and a little patience can learn how to make such an original gift on his own. Surely in the garage of almost every representative of the stronger sex, you can find all the tools necessary for production:

• punching discs (you can use a drill, but the result will not be so perfect);
• crossbar (some use a regular piece of reinforced pipe);
• vice (it is quite possible to do without them, but they make the process more convenient);
• ordinary hammer;
• a hammer with a plastic tip (to keep the design on the coin);
• calipers;
• file;
• fine-grained sandpaper;
• polishing;
• burner.

The first attempts to work with unfamiliar material may be unsuccessful. You need to be ready for this and not lose patience. Those who seek to achieve the desired result will surely succeed in the ring.

How to make a ring from a coin: instructions

First, you need to make a hole in the center of the coin. To do this, visually measure the center of the copper, and use a punching cut to cut a hole with a diameter of about 15 mm. You can use a drill for these purposes, but the result will be much worse. The use of a drill deforms the coin, creating ugly and difficult to remove burrs on it.

Important! To facilitate the production process, you can heat the product on a gas burner. However, you first need to determine the material from which the money is made. You can check this with a magnet. If the coin is attracted, it is made of steel alloy, if not, it is non-ferrous.

• for steel (it must be gradually heated and also carefully cooled, gradually removing it from the fire);
• for non-ferrous metals (alloys can be heated on a gas burner to a red-orange hue, and then sharply lowered into cold water).

During further operation, steel products can be periodically heated with a gas burner. This will greatly facilitate the work flow.

The resulting workpiece is put on a cone-shaped crossbar and, gently tapping with a plastic hammer, pass it further along the tube. At the same time, the edges of the coin are gradually bent, taking on the rough outlines of the future ring.

Having caught up with the ring to the diameter of the desired size, with the help of a plastic pipe and an ordinary hammer, the outlines of the ring are formed, which will be further processed and polished. In some sources, it is recommended to flip the ring on the crossbar in order to immediately give it the desired shape.

Further, the resulting ring needs to be polished and excess stiffeners removed. For this, a fine-grained skin and a drill with a coarse-grained skin attachment are used. The edge of the coin is smoothed and thinned, all protrusions and uncomfortable points are polished to make the ring fit and comfortable.

Then it remains only to finally polish the resulting jewelry. For this, you can use, for example, Goye's paste. In the end, the ring will acquire the correct shape and beautiful shade, and the chasing, carefully preserved, makes the jewelry original and attractive.

There is another way to make a ring from a coin. It requires a minimum set of tools:

• tablespoon;
• drill.

This production option is distinguished by high labor costs, so a man will have to be patient and diligent. In the production process, additional means may appear, with the help of which it will be more convenient for the master to achieve the result.

Important! The coin must be chosen in the correct size so that it is larger than the finger on which the bezel is planned to be worn in the future. You should not take multilayer coins at the first stages, the process of their processing is rather complicated.

Place the coin on a hard surface with an edge and. holding it with your fingers, we begin to tap with a spoon three times. Then the "blank" is turned and tapped again. For work, it is better to give preference to a massive spoon, so that it is easier to work with it.

Important! You need to knock on the coin quite often, but not too hard. The main thing is that the metal surface expands gradually. The tapping should be even so that no ugly dents appear.

After the source begins to approach the desired size, you need to start measuring it with a caliper and continue working until the ring takes on a rough final shape.

Using a drill, we drill a hole in the middle of the future ring. Then we expand it with a round file to the desired diameter. Further, it remains only to grind the ring to a perfect shine. First, a fine-grained skin is used, and then a dense felt fabric.

The decoration turns out to be shiny and beautiful. It looks like it came from the instrument of a famous jeweler and is made of precious metal. Armed with a simple and affordable tool, any man can independently make a ring from a coin and please himself with such a present to his beloved or close friends.

Hello, people with hands from the right places and just sympathetic.

I would like to tell you how I learned how to make super cool coin rings. But no. Super-cool did not learn.
In any case, so far I have not reached the level of "well, everything, now you can and at rest", so let's just call them ordinary rings from coins.

Under the cut, the path through thorns, garage workshops and the suffering of numismatists.

It all began four years ago, when the post “how to do it easily and simply” began to circulate actively on VKontakte. There were 9 photographs, in two of which they beat a coin with an iron hammer, and then it was all so beautiful and unharmed. It used US quotas (25 cents) and I had a bunch of quotas from a recent trip on my desk. This is a sign, I thought, and forgot about this post for two months, leaving the quarters covered in dust.

According to the laws of the genre, I came across this post regularly enough that at one point I realized that I hadn't had any new hobby for a long time and wondered how it was actually done. I took a few five-ruble coins, a couple of cans of beer and went to the garage to experiment. Now I understand the importance of the accident that I came across coins before 2009, copper-nickel, and not modern steel.

A couple of hours of experiments have shown that a “don't throw anything away” garage is good, but even that is not enough to comfortably work with unfamiliar material and a little specific tool is required. For example, punching discs, because when drilling with a drill, terrible nodules remained and the coin was bent from heat and pressure. Or a jewelry crossbar, which at first I tried to replace with some random, rusty, barely tapered piece of iron. Before the appearance of the video of the lawyer Yegorov, where he turned the bolt with a grinder from reinforcing bar in a lathe, about six months remained.

Googled YouTube, first ours, then foreign ones. I found out that a) in Russia no one does this, b) in the states it is already almost on stream and is in demand, c) initial investments are almost not required and everything is done quite simply (three times ha ha). The only conclusion was made - we must jump. Gutted the stash, went to Jewelry Tools, left the stash. In fact, the basic jewelry equipment (cutting, bolt, plastic hammer) required only about 5 thousand rubles. If I ordered all this on Ali, it would have turned out much cheaper, but I needed it here and now. You yourself know how it happens.

In fact, the manufacturing process itself is quite simple, although it is somewhat specific in terms of the tool used and is more like a manual for a lathe. Everything seems to be clear, but incomprehensible.

Of the tools you will need:

Jewelry tool:
- Cutting discs, such as this. It is possible with a drill, but it is long and inconvenient. On Ali, of course, there is also a felling:

Rigel, this is such a metal cone, without it there is nowhere, you can carve it out of reinforcing bar like Lawyer Egorov or, again, ali, you just need to look to make it steel (not plastic) and smooth, without steps:

A common tool: a vernier caliper, a vice (you can do without them, but it is more convenient with them), a regular hammer, a plastic (or textolite) hammer to save the pattern on the coin, a 20 cm piece of pvc pipe (preferably of different inner diameters ± according to the size of the desired rings), file, fine grain skin, polishing (goi paste, for example).

The algorithm is as follows:

Find the center of the coin, cut a hole about 10 mm in diameter. Cutting or drilling

We put the resulting washer on the bolt and tap it with a plastic hammer so that the edges of the coin begin to bend down.

Bending the washer at least 45 degrees, turn the bolt horizontally, resting the coin on some plate. We continue to knock on the coin so that it continues to press against the crossbar.

We turn over the coin on the crossbar with the wide part up. We put on the crossbar a piece of plastic pipe, resting the end on the coin and knocking with an ordinary hammer on the pipe from above, upsetting the coin below. The point is to remove the taper of the ring by making its walls parallel. We try not to overdo it with stretching, because without jewelry anchors and a vice, you will not be able to reduce the size of the ring.

We remove the ring, with a file or a coarse sandpaper, we clean the edges, then with a fine one, then we polish.

Done, you are amazing! But I warned that it looks like a lathe manual.

I used this algorithm to make rings for the first six months. Now the process has become much more complicated (but faster), and new tools have appeared in the equipment fleet, from a ring stretcher (pinocchio) to special cones ordered in a turning workshop.

However, even then there was enough enthusiasm that even a friend's broken finger would not prevent me from making it work. The plaster helped to keep the dremel correct.

About a year later, I finally learned how to work with silver. This was really a great achievement, because before that, silver coins were torn about half the time, which did not add optimism at all. It turned out that he simply annealed the silver incorrectly. The moment when jewelry education WOULD come in handy, but Google really came in handy. From the same series, the moment when I cooled a steel coin red-hot during annealing in water and could not understand why then the hammer crumbled against it. Literally "How the steel was tempered."

But, of course, it was not done without a variety of first pancakes, and it still cannot do. The box with "Pinocchio curves" is regularly replenished, albeit at a slower pace than the "ready-made" box, which is good news.

I worked then, three years ago, with a friend in my garage. There is, of course, a junk warehouse, like in any garage where the car is not parked. Well, a couple of free square meters for us. We don't need much. And once they call, they say, "We are here from the local television, found out about you, we want to come to the workshop, shoot a report." We were a little shocked, a little starred and, in our joy, said such nonsense to the whole TV that it’s still a shame to watch. And all this in a garage littered with rubbish.

Another "once" a friend wrote to me. “I’m here,” he says, “I’m organizing a cosplay festival, will you sell your rings there?” This is how the era of hand-made markets opened for me. First, local in Yekaterinburg, then in the neighboring regions. Last year I went to Moscow twice. We were warmly welcomed, thank you.

With these markets, I had to reactivate the skill "think up something from nothing" and create a stand. I didn't want typical jewelry, I'm a creative person, so this miracle was born. Plexiglass figure eight, laser cut slots, end rgb-tape and top illumination that have gone from "and so will come down" to an LED strip for 1600 lumens.

The year before last, due to circumstances, I had to leave my native warm garage and urgently find a replacement in the capital box. It was there that my dream of a separate workbench came true. I extended the legs of an ordinary office table, pulled everything together with corners and firmly attached them with corners and anchors to the floor and wall. Of course, it's not worth knocking on it with a hammer, the tabletop vibrates from impacts, but the vice and Pinocchio hold confidently, nothing crawls anywhere and is generally pleasant.

Over time, in the manufacture of rings, I wanted more in the literal sense of the word. Large coins are always more attractive than small ones, and the US craftsmen have mastered them long ago. Again, Google helped find the dreaded swedish wrap method, which essentially means pressing a finished ring into a polished inner cone to reduce size. It comes in very handy here, to protect the design of the coin, the plumbing Teflon sealing tape came in handy. And pvc pipes. And balls from bearings. And also all sorts of unknown garbage, which is beautifully laid out on the workbench in the previous photos. A complicated method, I say. But it turns out well.

So I got close, in fact, to the cherry on the cake. For a very long time I went to her - two years, almost. The first thought to make a GIF of creating a Morgan dollar ring arose when I made the very first animation from copper cents and immediately wanted to raise the bar. But then I still did not know how to work with silver. Then the second problem arose - the size of the coin. For the technologies existing at that time in my workshop, the coin was too large, 38 millimeters is not a joke. But this was also decided (the largest coin I worked with for this moment- this is the 1937 British crown, 38.6 mm). True, the GIF was still far away. It's one thing to learn how to make rings from such a coin, it's another thing to find the time, place and situation to film the process of creation. I will not describe typical everyday problems, everyone knows them, but they took several more months.

But, like everything in the world, it finally happened. Three hours of production and filming, five hours of processing and creation, totaling 8 hours of work for a 15-second animation. Amazing efficiency. Tag sarcasm.

Nowadays, when it is difficult to surprise people with something, but you really want to, you can do stylish ring from a coin that will amaze others. Especially if you choose an unusual specimen. For the first time, a way to make rings from metal kopecks was invented in America, and the person who did it was called Nicholas Hackman. They say that when Lenin married Krupskaya, they exchanged rings of coins. Now this idea gives enterprising people good earnings because such rings are sold for good money, and they are in demand.

There are two manufacturing technologies: one is simple, and the second is a little more complicated, but if desired, everyone can master it, you just need more tools. Let's start with the simpler one.

How to make a ring out of a coin

A ring can be made from absolutely any coin. If you wish, you can take a silver or gold one. To turn the ring into a coin, we need:

• Spoon.
• Drill.
• Zeal.

In the process, everyone will have additional tools with which it will be convenient for him to perform actions at a certain stage. If the ring is planned to be thick, then you need to take the appropriate coin, for example, a penny, in general, it should be larger than a finger in size. It is not recommended to take multi-layered pennies, at least until there is sufficient experience in manufacturing.

So let's get started. You need to take something metal, you can, for example, a hammer or other even piece of metal, put a penny on top of it on top of it and, holding it with your fingers, beat along its edge with a spoon. Doing this will take a long time, so you need to be patient. This is the only way you can understand how to make a ring out of a coin and whether it is worth it. It is better to take a massive spoon so that it is more convenient to work with it. You need to beat about three times, then turn a penny and start working further on a new site.

Production nuances

In this case, the main thing is to knock often, but not very hard, so that the surface from the blows gradually expands and is smooth. If you hit too hard, dents can appear and ruin the whole look. Another nuance is that you need to evenly tap the coin from all sides so that the surface is flattened evenly. It is worth developing a rhythm and moving in it constantly.

You need to continue knocking until the penny reaches the desired size. Making a ring from a coin requires a good eye. When the size of the jewelry becomes visually close to the desired one, you need to start measuring the diameter with a caliper in order to observe the exact parameters.

Drilling a coin ring

To drill a coin, you need to fix it. This can be done in a vice, after placing wooden blocks so as not to scratch the surface. If there is no vice, you can take two pieces of board, drill a hole in them by a millimeter or two smaller penny. Connect two bars and make small holes for self-tapping screws in the corners. After that, we insert a ring between the boards so that through the drilled opening there is access to the coin. We fix it securely and, holding this massive structure well, drill through the money. When we make a ring out of a coin, it is better to screw it on before drilling so that the drill does not jump off and does not scratch the surface.

Expanding the hole in the ring

Without pulling out of the clamp coin ring, you need to expand the hole in it. To do this, you can use a large drill or a round file of a suitable diameter by inserting it into the drill. In short, if there is no special instrument, then you just need to improvise.

Grinding the outer part

Now we already know exactly how to make a ring out of a coin, and it remains to polish it to a mirror shine. To do this, you need to take a bolt and nut of a size that is very close to the diameter of the inner circle of the decoration. We put it on the bolt, placing a piece of cloth, and then fix it with a nut. It is very important that the ring does not come into contact with metal or get scratched. We clamp the bolt into the drill, turn it on and grind the ring, first on the finest sandpaper, and then on felt or thick cloth. So the appearance of the ring will become dazzlingly perfect.

The inside can be easily sanded by inserting a straight piece of stick into the drill instead of the drill. You can hold the ring with pliers, having previously wrapped them in a thick cloth in several layers. That's all - the ring is made with your own hands from a coin, now it is worth polishing it by hand, and the fashion accessory is ready.

Ring with external coin design

To turn the ring pattern outward, you need to take a slightly different approach. This method is more complicated, but the result is many times more interesting.

The manufacturing scheme differs radically from the first option. You need to immediately drill a hole in the coin of such a size that the rim matches the thickness of the ring. After that, it will need to be expanded using a metal cone. It is firmly installed, a coin is put on top, on which we put a plastic tube and lightly hit from above. The coin gradually decreases, while expanding. When doing these steps, you need to feel the metal and watch the product to prevent the ring from breaking. After the coin has dropped a little, it must be removed and heated. This can be done in a fireplace or with a gas cutter.

After the penny heats up, you need to continue the same actions as before, only with a red-hot product. We do everything gradually, each time removing and heating the future ring. When the large circle, which is closer to the bottom of the cone, becomes of the required diameter, the product is turned over and is also put on the cone in a red-hot state. The work continues until both circles are of the same diameter. Here's how to make a ring with a pattern on the outside of a coin. After that, you need to grind the ring, as described in the first method.

It is not necessary to completely remove all carbon deposits when sanding. With a combination of shine and carbon deposits, the metal looks very impressive, and the pattern of the coin gives the ring a special charm. Such a stylish accessory will definitely be noticed by everyone around you.

You can also wear the ring yourself.

The history of the idea

Once upon a time with silver coin and hammer designer Nicholas Heckman created a homemade ring for his girlfriend. No one expected that it would turn out so well, and the relatives and the young lady herself were truly delighted with the work done. Subsequently, Heckman released a whole series of designer rings, which added to his fame and recognition. It happened that he had to suspend the sale of products, because they were in amazing demand. His a practical guide Heckman shared with the public and now everyone can become a home jeweler in a comfortable and convenient environment.

Tools for making a ring

Obviously, initially it is necessary to select a tool for making a hole in a coin, here the choice depends solely on the convenience of use in the preference of the manufacturer, for example: a drill, a hammer (plastic) and a bolt - quite a standard set for this type of work. In order to give the coin ring shine and completeness, you will need a piece of sandpaper. It follows from this that in technical terms, difficulties with the search for materials should not arise, everyone can act to the best of their skill and ingenuity.

Coin selection

In reality, the requirements for choosing a coin are not that extensive. There is a set of qualities that it must meet and, according to it, be processed to create a future product. First of all, it should be as strong as possible and not harmful to human life. In this case, brass, silver, bronze and steel are absolutely harmless. The color of the coin for the ring depends on individual preferences, but the size is a general indicator - coins equivalent to less than 1 ruble will not be suitable for work.

"Crazy hands" or "myself"

When choosing a coin for a ring, pay attention to the choice of material, silver has a great advantage. The first step will be to heat the coin until a bright red hue appears, but here it is important to find a middle ground and not overdo it, since the elements may suffer, and the coin itself will take a form that is not desirable for further work. At the end of such a procedure, the coin must be immediately immersed in cold water, a characteristic sound will be heard, but you should not be afraid of this, because this is considered an absolutely normal manifestation in such an interaction.

The next step in making a coin from a ring will be making a hole - this is a rather crucial moment, since here it is important to monitor symmetry and thickness, the larger the hole, the correspondingly thinner the product. Then the hammer and the crossbar come into their own. For those who do not know what a deadbolt is, it is a tool for making chain links that visually resembles a bar expanding towards the bottom. The coin should be positioned on the bolt and followed by precise, accurate hammer blows to the bottom, increasing in width. This is a rather laborious process that requires concentration and patience. You need to focus on the mark that is located on the crossbar and informs about the completion of work. Why a plastic hammer? Because any other risk of damage to the product increases tenfold. There is one more subtlety that must be taken into account. So that the product does not visually become like a cone, it must be periodically removed from the crossbar and shifted with the back side.

Video option

Grinding process

Grinding a coin ring is the most enjoyable process in making such a product. When the desired shape appeared and the coin turned into a real work of art, all that remained was to bring the matter to mind and give the ring a presentation. Sandpaper not only adds shine, but also smoothes the surface of the ring, after which it becomes smooth and pleasant to the touch.

There is another secret of how you can add extra smoothness to a coin ring. For this, a regular spoon is used, which is needed for light tapping on the surface of the ring. Here again, it is important to be careful and careful, because any intervention with more than necessary force can ruin everything that can be done up to this moment.

Safety engineering

Anyone who is going to create a ring from a coin should understand that this is a rather dangerous process,
which requires a certain approach and adherence to technical rules. The most important thing that a novice master should remember is about safety glasses, which should not be removed at the entire stage of the work. A mask and specialized gloves are also important, since when interacting with heated metal, every mistake made can result in serious injury. The work area must also be appropriate for the case and be protected from unwanted interference from production costs. All materials must be in sight, and the process itself must be carefully planned in advance. It should be remembered that when choosing a coin, preference is given to soft alloy coins, they are more suitable for work and appropriate for creating such a product.

Professional experience

In order to achieve the maximum shine of a coin ring, sandpaper alone will not be enough and more experienced craftsmen suggest using an abrasive composition. This can be considered quite appropriate advice, since this composition is used to treat the surface of hard materials, be it metal or rocks.

In any case, only by mastering the initial techniques, you can create your own unique, unique approach to making a ring and choose your own improvised means that only you can masterfully handle.