Ring of 5 ruble coins. How to make a ring from a coin? Drilling a coin ring

More and more often on the Internet there are photographs of rings made of coins, they look very beautiful and unusual, but it is not so easy to buy such a ring so that it also fits on your finger and is not expensive. But if you get used to it, then such a ring from a coin can be made at home with your own hands.

To make a ring from a coin, we need:

• Coin;
• Vice;
• Drill with a set of drills;
• Blowtorch;
• Hammer or chisel (you can get a better wooden ring, but the process will take longer);
• Metal conical pins and reinforced plastic pipes;
• Sandpaper and GOI paste.

How to make a ring from a coin with your own hands, step by step instructions:

First you need to mark the center of the coin with a center punch and hammer. Then we will need to drill a hole, for this we need to gently clamp the coin. This is done this way, take two boards (one thin another of any thickness suitable for you) or plywood a hole is drilled in one of them, then put between these boards so that the intended center of the coin is exactly in the center of the board hole and these two boards are compressed with clamps between themselves , our entire coin is securely fixed and you can drill a hole in it with a small diameter. After that, the hole needs to be sanded so that it is smooth and ready for further action.

Next, you need to heat the coin to red with a blowtorch or a gas burner, this will allow the metal to be “released” and the coin will not break when it is further unrolled on a cone and will make it more plastic and pliable. Then we immerse it in water.

Now we put our coin on the conical pin and begin to slowly beat the coin from above, unfolding it, it is better to use a wooden chisel for this, it will allow you to keep the drawing of the coin intact, and in order to unfold the coin, you can take a pipe that fits in diameter, which would fit on the pin and with careful blows on the base of the pipe, we push the coin further and further onto the rod, increasing the hole to the diameter we need (under the desired finger thickness). We would like to note that this is the most time-consuming and difficult part of the work, since at this stage you can easily damage the coin and you will have to start all over again with a new coin.

After all this, we should end up with something like this:

To prevent the ring from getting a conical shape, it must be removed and turned over from time to time during molding. We bring it to such a state that the cone shape is removed and it becomes the required diameter.

If after the work done by us the ring began to meet our requests and the drawing remained intact, then you can proceed to the next final step - polishing. This can be done in a variety of ways, such as using the Dremel with the correct brushes and GOI polishing wheels. You can also polish it by hand, the main thing is not to spoil the drawing. Before polishing, it is better to warm up the ring again and toss it into the water, when the scale comes off, the drawing will appear better.

Thus, you can make rings of various thicknesses (wide or thin) from coins, those who are seriously engaged in the creation of rings from coins buy collectible coins for their work, but if you are just a beginner, then it is better to make the first ring from a coin from more affordable coins, since there is a great risk of spoiling it. This is far from the most the only way make a ring from a coin, you can find others on the network, but this is perhaps the most affordable of them.

Examples of how coin rings work:

Nowadays, when it is difficult to surprise people with something, but you really want to, you can do stylish ring from a coin that will amaze others. Especially if you choose an unusual specimen. For the first time, a way to make rings from metal kopecks was invented in America, and the person who did it was called Nicholas Hackman. They say that when Lenin married Krupskaya, they exchanged rings of coins. Now this idea gives enterprising people good earnings because such rings are sold for good money, and they are in demand.

There are two manufacturing technologies: one is simple, and the second is a little more complicated, but if desired, everyone can master it, you just need more tools. Let's start with the simpler one.

How to make a ring out of a coin

A ring can be made from absolutely any coin. If you wish, you can take a silver or gold one. To turn the ring into a coin, we need:

• A spoon.
• Drill.
• Zeal.

In the process, everyone will have additional tools with which it will be convenient for him to perform actions at a certain stage. If the ring is planned to be thick, then you need to take the appropriate coin, for example, a penny, in general, it should be larger in size than a finger. It is not recommended to take multi-layered pennies, at least until there is sufficient experience in manufacturing.

So let's get started. You need to take something metal, you can, for example, a hammer or other even piece of metal, put a penny on top of it on top of it and, holding it with your fingers, beat along its edge with a spoon. Doing this will take a long time, so you need to be patient. This is the only way you can understand how to make a ring out of a coin and whether it is worth it. It is better to take a massive spoon so that it is more convenient to work with it. You need to beat about three times, then turn a penny and start working further on a new site.

Nuances of production

In this case, the main thing is to knock often, but not very hard, so that the surface from the blows gradually expands and is smooth. If you hit too hard, dents can appear and ruin the whole look. Another nuance is that you need to evenly tap the coin from all sides so that the surface is flattened evenly. It is worth developing a rhythm and moving in it constantly.

You need to continue knocking until the penny reaches the desired size. Making a ring from a coin requires a good eye. When the size of the jewelry becomes visually close to the desired one, you need to start measuring the diameter with a caliper in order to observe the exact parameters.

Drilling a coin ring

To drill a coin, you need to fix it. This can be done in a vice, after placing wooden blocks so as not to scratch the surface. If there is no vice, you can take two pieces of board, drill a hole in them by a millimeter or two smaller penny. Connect two bars and make small holes for self-tapping screws in the corners. After that, we insert a ring between the boards so that through the drilled opening there is access to the coin. We fix it securely and, holding this massive structure well, drill through the money. When we make a ring out of a coin, it is better to screw it on before drilling so that the drill does not jump off and does not scratch the surface.

Expanding the hole in the ring

Without pulling the coin ring out of the clip, you need to widen the hole in it. To do this, you can use a large drill or a round file of a suitable diameter by inserting it into the drill. In short, if there is no special instrument, then you just need to improvise.

Grinding the outer part

Now we already know exactly how to make a ring out of a coin, and it remains to polish it to a mirror shine. To do this, you need to take a bolt and nut of a size that is very close to the diameter of the inner circle of the decoration. We put it on the bolt, placing a piece of cloth, and then fix it with a nut. It is very important that the ring does not come into contact with metal or get scratched. We clamp the bolt into the drill, turn it on and grind the ring, first on the finest sandpaper, and then on felt or thick cloth. So the appearance of the ring will become dazzlingly perfect.

The inside can be easily sanded by inserting a straight piece of stick into the drill instead of the drill. You can hold the ring with pliers, having previously wrapped them in a thick cloth in several layers. That's all - the ring is made with your own hands from a coin, now it is worth polishing it by hand, and the fashion accessory is ready.

Ring with external coin design

To turn the ring pattern outward, you need to take a slightly different approach. This method is more complicated, but the result is many times more interesting.

The manufacturing scheme differs radically from the first option. You need to immediately drill a hole in the coin of such a size that the rim matches the thickness of the ring. After that, it will need to be expanded using a metal cone. It is firmly installed, a coin is put on top, on which we put a plastic tube and lightly hit from above. The coin gradually decreases, expanding at the same time. When doing these steps, you need to feel the metal and watch the product to prevent the ring from breaking. After the coin has dropped a little, it must be removed and heated. This can be done in a fireplace or with a gas cutter.

After the penny heats up, you need to continue the same actions as before, only with a red-hot product. We do everything gradually, each time removing and heating the future ring. When the large circle, which is closer to the bottom of the cone, becomes of the required diameter, the product is turned over and is also put on the cone in a red-hot state. The work continues until both circles are of the same diameter. Here's how to make a ring with a pattern on the outside of a coin. After that, you need to grind the ring, as described in the first method.

When sanding, it is not necessary to completely remove all carbon deposits. With a combination of shine and carbon deposits, the metal looks very impressive, and the pattern of the coin gives the ring a special charm. Such a stylish accessory will definitely be noticed by everyone around.

The year of manufacture is minted on the coins. This means that you can make a ring from a coin with a significant date for you or the person to whom you will give your product. This will be an original themed gift made by yourself. The method proposed by the author of this idea is suitable for any coins.

To make a ring from a coin disk, you need to make a hole in it and then unfold the resulting blank with a Morse taper. The smaller you make the hole, the wider the ring will be. However, it will be difficult to make a wide ring, since when unfolding the coin, you will have to try not to tear it or crush it.

The actual work on turning the coin is carried out with a stand with a wide opening. To do this, you can use a bearing, pipe end or other device. Warming up the workpiece, you can protect it from rupture. Experience has shown that paper is a good protector that can protect the inside of the ring from damage. To push the workpiece, it is advisable to take an aluminum tube, since this metal is softer and will not damage the future ring.

After creating an annular blank, only the grinding of the product remains.

The second helpful video from this master is on the topic of coin rings.

As additional information, another video on the same topic, but with the approach of a foreign master.

And here is another video tutorial on this topic.

Unique jewelry has always attracted attention, just remember what battles unfolded in the Lord of the Rings. In this video you will learn how to make a unique ring with your own hands from regular coin... In our case, it will be in rubles.

Mark the center of the coin and make a hole in it. We cut the resulting burrs with a file. Then we need to put this blank on a metal rod. In the case shown, this will be a core. Having made an emphasis on the board, we begin to gently tap it and this must be done at an angle to the workpiece so that the side of the coin with the pattern begins to turn outward.

Our workpiece has outgrown the core and now, to further bend the sides of the money and enlarge the hole, we will use a machined sleeve from the key and then a processed construction plumb line - ideally, it is better to have one rod with an increase from small to large diameter. If there is a vice, then they will greatly simplify the task. But be careful, the vice can ruin the drawing.

Let's warm up well and start forging ours. This process is very time consuming and you can hardly manage it in one hour. After we have achieved the desired size of the ring, we will grind its ends on a grindstone and then process the edges with a round file.

When making the first coin, 2 mistakes were made that you want to avoid. The author of the video did not immediately use the heating of the coin and polished the ring too much, but it turned out but without a pattern.

Let's try again. Let's make a ring from another 1 ruble coin. Let's make a hole, warm it up well and start forging. We repeat this process until we get the desired result. After the ring has taken the desired shape, we will process the edges. Next, we will begin to carefully sand it, and the most important thing here is not to grind off the entire drawing. With a little skill, many will do much better.

Many people have long made from commemorative coins rings for yourself and loved ones. Just like collecting coins from all the countries you've visited, you can forge rings to remind you of your happy vacation days. Such rings will not oxidize like regular jewelry, and will serve you for a long time. You can make an engraving pattern on the outside of the ring, or on its face. There are at least two ways to make a ring out of an ordinary coin: forge it with special tools or use improvised means, namely a spoon and a drill. You will see illustrative examples in this article.

How to make a ring out of a coin: method number 1

This is where you need special tools:

• a burner to soften the metal of the coin and shape it faster;
• jewelry bolt, of course, you can use any steel shape, the diameter of which is similar to a finger;
• hammer, craftsmen recommend plastic hammers so that the drawing remains the same embossed;
• dremel for grinding and cutting a circle, you can do with a drill with homemade grinding attachments.

In addition to this list, stock up on rags, cleaning products and patience, since not everyone succeeds in the first experience.

• The hardest part: choose the area to cut the ring. The example below clearly shows that some sides of the coins are completely unsuitable for rings. Twist it and see which side will look beautiful, only then make notes. Take a marker and mark the size of the future armhole.

• Drill a small hole so that the ring can be slipped onto the jewelry wedge. Be careful, you do not need to drill the diameter of the finger right away, since the metal will stretch strongly during the forging process.

• Heat the coin with a burner until the metal turns reddish, the ring darkens slightly. Try to do this evenly so that all parts are warmed up, otherwise you run the risk of making a non-proportional ring in which one part will be punched better than the other.

• Slip a coin onto the blank and start hitting with a hammer. This is a rather tedious and lengthy exercise. As soon as the coin cools down and is hard to forge, remove and heat it up again. Please note that a bad blank will not withstand the heating of the coin directly on it, so do not be too lazy to remove the future ring, heat it up, and only then put it back on.

• Gradually, the coin will take on a ring shape. Do not stop until it is proportional and equally round on all sides.

• You just have to polish the ring in a way that is available to you: whether it be manual polishing with a coarse cloth, dremel or homemade drill bits.
• Cover the inside of the ring with clear varnish to eliminate copper residues on your fingers. Such decoration will last a long time and will bring many pleasant memories.

How to make a ring out of a coin: method number 2

A curious way to create a ring. To do this, you will need even more patience and an ordinary spoon. In this case, you do not even need to heat the product.

• You need to put the coin on its edge and knock on it with a steel spoon until it begins to deform. This work is laborious and long, but with improvised means. Tap with a spoon until the rib width is acceptable to you.

• Once you're happy with the width, drill out all the metal from the middle and start sanding the coin. Use wool or other rough materials that you have on hand.

• As a result, you will get beautiful rings from a five-ruble coin.

The disadvantage of this method is that you cannot adjust the size of the ring, they will only fit on a wide finger.

Don't be discouraged if your ring didn't work the first time. Try again and get the hang of it very soon.

Owned by Nicholas Heckman. He independently took up the hammer and created such an accessory for his beloved. The girl was amazed, however, like all her relatives. The general admiration inspired Nicholas so much that he began to improve his creation and, as a result, released a whole series of original silver rings, but after that he stopped his business. Today, everyone can do this work for his beloved. A homemade ring will be a great surprise, because what is most valuable is what you create with your own hands.

What is needed to make a coin ring?

First of all, you will need a plastic hammer, bolt, drill, or any other tool with which you can make a hole. This can be, for example, a special apparatus. Use what is convenient for you. Prepare sandpaper to add shine. It will come in handy after completing the main work.

How to choose a coin for a ring?

It should be noted that it must meet certain requirements. Main characteristics:

• strength;
• safety;
• the size;
• Colour.

Brass, silver, bronze and steel are not hazardous to human health. That is why you should give preference to these particular materials. Copper and nickel can cause skin diseases and body poisoning.

Pay attention to size. Small coins, up to 1 ruble denomination, will definitely not work.

DIY your ring: step one

First, decide which coin you will be making a ring from. Silver is an excellent material. Then heat it red-hot to make it elastic, but don't overdo it. Otherwise, the coin will be deformed, and some of the elements will be lubricated. After it acquires a red hue and slightly whitens, drop it sharply into cold water. At this point, you will hear a hiss. Don't be alarmed - this is a common occurrence.

We pass to the main work to make a ring from a coin with our own hands. Use a drill to make a hole. Make sure it is even. The larger it is, the thinner the ring, but don't overdo it. Otherwise, the coin may burst.

Once you have made the hole, you will need a plastic hammer and bolt, thanks to which you can select the required size and create the shape. This tool is like a metal stick that expands from the bottom to the end. Put a coin on the bolt and with even hammer blows lower the ring down, stretching it. This is a very painstaking process. Try to tap the product lightly, otherwise it may deform. Gently adjust the ring to the size you want. There is a special marking on the crossbar. When you get to a certain level, remove the ring.

What do you need to know?

To make a ring from a coin, you only need to use a plastic hammer. If you use metal, you risk damaging the smallest elements of the coin. Accordingly, the surface of the product will turn out to be uneven, even after sanding.

Making a ring from a coin is not easy, but if you follow the rules, you will certainly succeed. There is one more very important nuance. To prevent your product from taking on a conical shape, from time to time remove it from the crossbar and turn it over. This is the hardest part, because choosing the right size is not as easy as it seems at first glance. Follow the instructions carefully, and you will certainly be able to make a ring out of a coin.

When removing the item from the deadbolt, use a pair of pliers or clamping pliers to avoid scratching it.

Safety regulations

When working with hot metal or silver, be sure to wear special gloves, because you risk getting burned. It should be noted that at the first stage of manufacturing, when you work with a drill, you need to wear or a mask. Equip your workplace in accordance with all safety regulations. When punching a hole in the coin, cover the table with a sheet of fiberboard.

Grinding

When wondering how to make a ring from a coin, you need to carefully familiarize yourself with the manufacturing process. All instructions are detailed in this article. As we said, the most difficult part of the work is creating the form. Sanding is the most enjoyable process. When the ring is ready, you can enjoy the fruit of your labor to the fullest. It remains only to add gloss and shake off excess husk.

Create shine and bring beauty

In order for the surface of the ring to turn out smooth, you can make several dozen blows with an ordinary spoon. They must be light, otherwise you risk deforming the ring. To make it smoother, use emery paper or a special electric tool to remove any exterior imperfections. The surface of the ring, the photo of which you see below, will take on a polished look.

It should be noted that there are several types of polishing tools: coarse grain and rough. Choose what suits you best.

The manufacturing method used in this article is quite complex, but the result is a perfect product that will delight you throughout years... After polishing, you can decorate the ring with a beautiful engraving or original pattern. However, the result of your work depends on your efforts.

How to organize your workflow?

It is necessary to prepare a workshop where you will have everything at hand. Choose soft alloy minted coins as your material. Always remember this, because the preparatory process is no less important than the work itself.

What other technologies are used to make a ring out of a coin? As you know, there are several methods. The second can be used as an alternative. It begins with the fact that you need to put a coin on the edge and cover it with some form. An ordinary spoon is suitable for this. This manufacturing method differs from the previous one in that the coin does not need to be melted. Here it is necessary to flatten the rib, applying strong blows hammer. Work the edges evenly. Periodically look at what happened. After the edges of the coin are rounded, drill the hole, but not completely. Stop the drill before it goes right through. Then sand the inside and sand the outside.

How to make your ring perfect? Take an abrasive compound and apply it with a small piece of cloth. Wipe several times to achieve a mirror finish. After that, prepare a grip, due to which you can firmly hold the coin in your hand. It is necessary that his lips have a curved shape. This will provide protection from dents and unwanted scratches. You can also use rubber felt or paper backing (any soft material will work).

The next step is to enlarge the hole in the center. Make sure that the drill does not slide to the sides, otherwise all the work done will go down the drain. At this stage, you need to be patient. Use gentle and painstaking movements to highlight the circumference of the ring. After you have made the ring of the required size, you need to level the inside with an emery roller.

Making a ring from a coin is a rather painstaking process. It requires precise movement and adherence to instructions. There are many technologies. You can use a variety of crafting tools. For example, you can use ordinary pliers as a clamp, wrapping them with soft material. This will prevent damage to the surface of the product. There are also many different polishing machines available to make the process easier.

A coin ring is an original and romantic gift. Any girl will appreciate such a broad gesture.